RC car not responding to controller

When the RC car not responding to the controller, don’t take it apart until you check it out.
A stagnant (never starting from scratch) or slow RC is frustrating. But a lot of times, something very simple and very basic is wrong. Before you take it apart (or crush it to pieces), take a deep breath and review every common, unbiased thing you can do to fix the problematic part first. Even if you realize this, it’s not a problem. Double-check obvious and simple questions. You might be surprised. Alternatively, you can rule out simple problems before attempting more complex repairs and adjustments.

Check the on/off switch

Sure, it can be awkward, but sometimes the problem is as simple as not turning on the transmitter (probably not some toys if there is a switch) and RC cars. Some RCs may require a flashlight to clearly tell which is on and which is off. Always check first. If simply turning it on doesn’t work, make sure the switch is in the off position before scrubbing the inside of the RC.

Replacement battery

Replacing the battery in an electric RC is expensive and cumbersome. Batteries are often the source of many RC problems. If it doesn’t work at all, runs very slowly, or stops suddenly, it could be battery-related.

  • Missing battery. Check RC and transmitter.
  • Incorrect installation. Make sure the battery is facing the correct direction and fully inserted into the small slot.
  • Old battery. Try new RC batteries. Or, if you’re using a cheaper brand, try another brand. If using a battery pack, make sure it is fully charged.
  • Corrosion. Corrosion can occur if it does not respond to the controller or if the battery compartment is exposed to moisture and air. In addition to replacing the battery, clean the battery contacts.

Add fuel

The Nitro RC can be a complex and demanding piece of equipment. Check the fuel tank before making engine settings. do you have fuel? Is it fresh? Is there a kink in the fuel line? If a quick visual inspection does not reveal an easy solution, a complete overhaul of the fuel system may be required. It’s not difficult, but it takes more time.

Use the correct transmitter and frequency

If it’s a remote control toy, make sure you have the correct transmitter. If you have a lot of RCs, you can easily combine them. If you are buying a used RC, the seller may have provided the wrong transmitter. Look for frequency tags on transmitters and vehicles. (Usually somewhere on the bottom, near the on/off switch or near the battery compartment. Both should be the same (eg 27MHz or 49MHz, etc.). You have the wrong transmitter, you need to get the right one.

For hobby-grade RCs, check the crystals on the transmitter and receiver. Make sure you have a matching set. If there are other sets available, please try them.

Check your antenna

Car and transmitter antenna. If your RC has a telescopic antenna on the transmitter (or vehicle), make sure it is fully extended. While this makes the RC not work at all, it may have limited range or perform poorly.
Make sure the receiving antenna on the remote control is installed correctly (do not skew or break, do not touch the metal parts inside the remote control, do not drag on the ground). etc”

Servo test

A sign of a problem with the servo is when the RC only responds to some commands from the transmitter and not others. For example, the wheels turn but cannot move forward. Unplug the servo from the receiver and connect it to a working receiver (make sure the receiver and transmitter frequencies are correct). If the RC is still not responding, it may be time to repair or replace the servo, not the receiver or transmitter. If you’re not used to the internals, or if your receiver isn’t working properly, take your RC to a hobby store or RC club and ask for help with a test.


Loose or damaged cables can cause many problems. If the steering works but the RC doesn’t move, there may be a loose wire on the motor. Lack of steering can signal the steering servos to be loose. If your RC doesn’t seem to be getting power at all, and you know the battery is good, there may be a loose or disconnected wire in the battery pack or battery case that’s causing the problem. A loose connection or reconnecting the connector may solve the problem.

Gear reset

A slippery gear can stop the RC from moving. No need to replace the gear unless it comes off, just tighten the pinion and realign it with the spur gear. If your RC rubs and won’t move, there is a problem.

Steering arm damage repair

The RC will work, but shaking will damage the steering arm. Find a long strip of plastic near the front wheel (like a pull rod on a real car). Is one broken? You can replace it with hard wire, such as a coat hanger.

Statement: This article comes from the Internet. If there is any infringement, please contact me to delete it.

Leave a Reply

Your email address will not be published. Required fields are marked *